mutz
Recruit
Posts: 5 
|
Post by mutz on Dec 2, 2017 13:54:54 GMT
Hi there
I tried to load a saved flight, which worked. Teh Helicopter is there engine off (what is good) but unfortunately no ship. I can start etc. the helicopter does not "fall" into the water. All normal, except there is no ship below the helicopter.
Any ideas what I did wrong?
Thanks and cheers
Mutz
simulation@mutznet.ch btw using P3DV4.1
|
|
|
|
Post by Ripcord on Dec 3, 2017 0:54:35 GMT
Mutz, please give let me know which saved flight is giving you this problem. All of them? Or just some? Or only one?
|
|
mutz
Recruit
Posts: 5
|
Post by mutz on Dec 3, 2017 14:08:07 GMT
Thanks for the fast reply.
Indeed it is the case in all flights. Carriers and any other ships, the Helicopter is in the air, but no ship below. Except with the Nimitz where I ended up in the water :-)
I have a resolution of 3840x2160 (4 K) . if it is a time issue I leave in Switzerland --> UTC -1h.
Otherwise all ships are there in the Boat folder under simobjects. With Aicarrier I can all your ships activate as intended.
Cheers Mutz
|
|
|
|
Post by Ripcord on Dec 3, 2017 16:46:43 GMT
Mutz
One quick thing to check -- do you have AI boat traffic set to at least 10% or higher?
That would be one possible cause.
Ripcord
|
|
|
|
Post by Ripcord on Dec 3, 2017 20:52:20 GMT
Also, please look under GENERAL OPTIONS and tell me which boxes are checked...
|
|
mutz
Recruit
Posts: 5
|
Post by mutz on Dec 4, 2017 11:45:40 GMT
Ok I am in the office and have no access for the moment.
However, the ship traffic is set to 100% :-)
The General Options issue I can answer this evening (in about 7 hours)
Cheers Mutz
|
|
mutz
Recruit
Posts: 5
|
Post by mutz on Dec 4, 2017 20:29:17 GMT
Ok, Not ticked is Pause on task switch, Use system time for Default secenario (have changed this one without effect), Enable content error Reporting pand Broadcast GPS data to network.
traffic ships 100%, Leisure Boats 50%, Road vehicles 24%, Air traffic both 100% and Aiport vehicles Density low.
Realism all 100%, Detect crashes enabled including stress damages. The rest is realistic, all damage is activated including Visual G-effects.
Display FXAA off, AA None, Anisotropic 2x, Textures 2048x2048, Vsync off and unlimited, Mipmap VC Panels ticked. --> Geforce GTX 980
Still no joy :-(
Cheers Mutz
|
|
|
|
Post by Ripcord on Dec 4, 2017 21:35:34 GMT
Mutz, do this for me please -- run a test of one of the saved flights, and please note the sim time (GMT or Local, but important to indicate which).
Of course, let me know flight you choose. Thanks
|
|
|
|
Post by Ripcord on Dec 4, 2017 23:52:19 GMT
Mutz, also sir, please advise, do you have FSUIPC installed?
|
|
mutz
Recruit
Posts: 5
|
Post by mutz on Dec 6, 2017 19:24:59 GMT
Ok Sorry for the late answer, I was out of the office for 2 Days.
Well you found it :-) In FSUIPC under MISC was the box ticked which fixed the starting time ALWAYS on the system time.
Sorry for the confusion. So I made some different flights , every where the boat was there. Problem solved!
Thanks a lot for your support! A very nice product!!!
Cheers Mutz
|
|
|
|
Post by Ripcord on Dec 6, 2017 20:43:07 GMT
Great news. Now we know the solution!
|
|
